Mercedes W163
+ Mercedes-Benz cars of a class M (W163)
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
- Power supply system and production of the fulfilled gases
+ Power supply system of petrol engines
+ Power supply system of diesel engines
- Systems of release and decrease in toxicity of the fulfilled gases
Removal and installation of system of production of the fulfilled gases
Replacement of forward sections of system of production of the fulfilled gases on petrol models
Removal and installation of catalytic converters on diesel models
Removal and installation lambda probes
Removal and installation of the EGR valve, - M112/113
Removal and installation of a cooler of EGR, - diesel models
Removal and installation of the air pump, - M112/113
Removal and installation of a coal adsorber, - petrol models
Removal and installation of the broad tank of accumulation of fuel evaporations, - appropriately completed model 163.113/154/128
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of catalytic converters on diesel models M612 Primary catalytic converter
Details of installation of primary catalytic converter on models 163.113 (the series 612 engine)
|
|
- Details of installation of primary catalytic converter on models 163.113 (the series 612 engine) are shown on an illustration to which all references which are found in the text belong.
- Remove the lower section of a noise isolation.
- Having squeezed the Swede disk springs (see an illustration
of the Detail of installation of forward section of system of production of the fulfilled gases on models 163.136 (the series 111 engine)), unbend the screw-driver a steel uvula and release spring connection of fastening of primary catalytic converter (120/1) to a pipe (111) forward sections of system of production of the fulfilled gases.
- Turn out a bolt (1) of fastening of primary catalytic converter (120/1)
- Remove the air cleaner.
- Release a collar of fastening of primary catalytic converter (120/1) to a turbocompressor (110).
- Remove the catalytic converter (120/1).
- Installation is made upside-down, - track reliability of a zashchelkivaniye of disk springs, you make tightening of a fixing collar after fixing of the catalytic converter on a basic arm.
|
|
Utilization of the failed catalytic converters has to be made with respect for legislative rules! |
|
|
Assembly of forward section of system of release with the main catalytic converter
Details of installation of assembly of forward section of system of production of the fulfilled gases with the main catalytic converter on models 163.113 (the series 612 engine)
|
|
- Details of installation of forward section of system of production of the fulfilled gases with the main catalytic converter on models 163.128 (the series 628 engine) are shown on an illustration to which all references which are found in the text belong.
- Tire out the car on the elevator.
- Remove the noise-insulating element established under transmission, - do not remove the central section of a noise isolation.
- Having squeezed the Swede disk springs (and and b), unbend the screw-driver a steel uvula and release spring connection of fastening of a pipe of forward section of system of release to primary catalytic converter.
- Give nuts (3) fastenings of forward section of system of release to a basic arm (4) on transmission.
- Separate assembly of forward section with the catalytic converter (2) from the back muffler (6).
- Having given back, take assembly (2) from under the car. Check a condition of thermofilters of the bottom, replace defective units.
- Installation is made upside-down, - track reliability of a zashchelkivaniye of disk springs, you make tightening of a fixing collar after fixing of the catalytic converter on a basic arm.
|
|
Utilization of the failed catalytic converters has to be made with respect for legislative rules! |
|
|
M628 Assembly of forward section of system of release with the main catalytic converter
Details of installation of assemblies of forward sections of system of production of the fulfilled gases catalytic converters on models 163.128 (the series 628 engine)
Details of installation of assemblies of forward sections of system of production of the fulfilled gases with catalytic converters on models 163.128 (the series 628 engine)
|
|
- Details of installation of assemblies of forward sections of system of production of the fulfilled gases with catalytic converters on models 163.128 (the series 628 engine) are shown on illustrations to which all references which are found in the text belong.
- Tire out the car on the elevator.
- Remove forward wheels and loker of protection of wheel arches.
- Remove the thermofilter (1), - only for the left section.
- Remove the noise-insulating element established under transmission, - do not remove the central section of a noise isolation.
- Remove the torsion bar (3).
|
|
Only the bar located from one board with the replaced section of system of production of the fulfilled gases is removed! |
- Turn out bolts (4) arms (5), - only for the left section.
- Turn out a bolt (6) of an arm (7), - only the right section.
- Release the welded collar (8) of fastening of forward section to the muffler.
- Give nuts (10) of fastening of forward section to a basic arm (11) on a transmission case, - nuts are subject to replacement without fail.
- Prop up transmission and remove a back support of the power unit (see the Head Dvigatel).
- Separate forward section from a final collector / turbocompressor and the back muffler and take it from under the car.
- Installation is made upside-down.
|
|
Utilization of the failed catalytic converters has to be made with respect for legislative rules! |
|
|
|
|