Mercedes M-Class W163

since 1997 release

Repair and operation of the car



Mercedes W163
+ Mercedes-Benz cars of a class M (W163)
+ Governing bodies and methods of safe operation
- Current leaving and service
   Active system of the warning of the term of approach planned THAT (ASSYST)
   Schedule of routine maintenance
   General information on settings
   Check of levels of liquids, control of leaks
   Check of a condition of tires and pressure in them, designation of tires and disks of wheels, rotation of wheels
   Replacement of motive oil and oil filter
   Check of the brake system
   Check of a power supply system, replacement of the fuel filter
   Check of a state and replacement of hoses of a motive compartment, localization of leaks
   Check of a condition of multicostal belts of the drive of auxiliary units
   Check of functioning of the cooling system and frost resistance of cooling liquid, liquid replacement
   Check of a condition of system of production of the fulfilled gases
   Replacement and check of the ATF level, replacement of the AT filter
   Visual check of tightness of automatic transmission
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of boots of power shafts
   Check of the air conditioning system
   Lubricant of limiters of doors and cylinders of locks
   Visual control of a seat belt and block of a safety cushion
   Check of operability of headlights and horn
   Check of a state and replacement of brushes of screen wipers
   Check of a condition of the battery, care of it and charging
   Replacement of the saloon filter
   Replacement of brake fluid
   Check and replacement of spark plugs, check of a condition of high-voltage wires (petrol models)
+ Engine
+ Cooling systems, heating and air conditioner
+ A power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


General information on settings

The term "control" is used in this manual rather for designation of a complex of procedures, than one separate procedure.

If from the moment of purchase of the car the schedule of routine maintenance is strictly observed, frequent inspections of level of liquids and a state subject to the increased wear of components will be carried out as it is offered in this manual, the engine will long remain in the good working condition, and need for carrying out any additional work will be minimized.

Is more often, however, happens so that the engine works inefficiently owing to neglect with regular service. Even more often it happens upon purchase of the used car which owners did not trouble themselves frequent and regular checks and service. In this case, besides performance of ordinary procedures for routine maintenance, it will be necessary to make setup of the engine.

The first step in any procedure of control or diagnostics for the purpose of improvement of operation of the engine is check of extent of compression in cylinders. Check of a compression (address the Head Dvigatel) will help to define a condition of internal components of the engine and has to serve as the index when carrying out control and repair. If, for example, check of extent of compression indicates serious internal wear of the engine, usual control will not help to improve its work and will be waste of time and money. As the procedure of check of extent of compression is extremely important, the expert owning the equipment which is specially intended for this purpose has to see off it.

Reduction of the engine in the good working condition most often requires performance of the following procedures:

Minimum settings

· Check of level and a condition of all liquids connected with operation of the engine (see the Section Check of Levels of Liquids, control of leaks).

· Check of a condition of all hoses of a motive compartment (see the Section Check of a State and Replacement of Hoses of a Motive Compartment, localization of leaks).

· Check of a state and adjustment of a tension of belts of the drive of auxiliary units (see the Section Check of a Condition of Multicostal Belts of the Drive of Auxiliary Units and Head Engine).

· Cleaning, survey and check of battery charging (see the Section Check of a Condition of the Battery, care of it and charging).

· Replacement of spark plugs (petrol models - see the Section Check and replacement of spark plugs, check of a condition of high-voltage wires (petrol models)) / an incandescence (diesel models - see the Head of the Power supply system and production of the fulfilled gases).

· Survey of VV of an electrical wiring (see the Head Sistemy of electric equipment of the engine).

· Check of a condition of the filtering air cleaner element (see the Head of the Power supply system and production of the fulfilled gases).

· Check of a condition of components of the cooling system (see the Sections Check of a State and Replacement of Hoses of a Motive Compartment, localization of leaks and Check of functioning of the cooling system and frost resistance of cooling liquid, liquid replacement).

General settings

In addition to the settings listed in the previous list:

· Check of a condition of components of system of ignition (petrol models) / preheat (diesel models) (see the Head Sistemy of electric equipment of the engine).

· Check of a condition of components of system of a charge (see the Head Sistemy of electric equipment of the engine).

· Check of a condition of components of a power supply system (see the Head of the Power supply system and production of the fulfilled gases).

· Replacement of VV of an electrical wiring (see the Head Sistemy of electric equipment of the engine).