Mercedes W163
+ Mercedes-Benz cars of a class M (W163)
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ A power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Transmission line
- Brake and auxiliary systems
General information and security measures
Check of the brake system on leaks
Check of serviceability of functioning of the vacuum amplifier of brakes
Check of retaining valve
Removal and installation of the main brake cylinder
Removal and installation of the vacuum amplifier of brakes and sensor of the course of a diaphragm of BAS
Removal and installation of the ETS/ESP hydromodulator
Removal and installation of the hydraulic lines laid between GTTs and the ETS/ESP hydromodulator
Assessment of degree of wear and replacement of brake shoes
Replacement of brake hoses
Removal and installation of a support
Removal and installation of a brake disk
Replacement of boots of the parking brake
Pumping of the brake system
Removal and installation of pedal knot and sensor switch of stoplights
Removal and installation of a pedal of raising of the parking brake
Removal and installation of hummock assembly of the drive of the parking brake
Adjustment of the drive of the parking brake
Removal and installation of wheel ABS/ETS/ESP sensors
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of the main brake cylinder
GTTs installation details (on the example of models with AT, version 1)
GTTs installation details (on the example of models with AT, version 2)
Removal/installation of the brake amplifier
Removal/installation of the brake amplifier
|
|
- Illustrative material according to the procedure of removal/installation of the brake amplifier is presented on illustrations to which all references which are found in the text belong if the return is not specified especially.
- Open a cowl and record it in vertical position.
- Remove panels of finishing of the power unit and a cover of the assembly block of safety locks/relay.
- Disconnect an electrical wiring from the GTTs (10) tank.
- Disconnect the vacuum line (8) from the brake amplifier (16).
- On diesel models release from clamps on a partition the vacuum line (8a), and also the auxiliary line.
- Disconnect from the vacuum pump (24) a hose (27).
- Release hoses (21) from an arm (28).
- Separate hoses from the assembly block of safety locks/relay and take away from to the engine.
- Previously having marked, disconnect from GTTs brake tenches (5), - at once to a zakuporta the open ends of nipple sockets.
- At the corresponding complete set disconnect an electrical wiring from sensors 1 and 2 of brake pressure of ESP (B4/1 and V34/2), - release clamps from the lower parties of sockets.
- Give самоконтрящиеся nuts (19) of fastening of GTTs (1), - nuts are subject to replacement without fail.
- At the corresponding complete set remove the thermofilter (1b).
- At the corresponding complete set remove a siren of the anticreeping alarm system from a partition of a motive compartment.
- Having pulled strictly horizontally, remove GTTs from the block of the brake amplifier and transfer it to a workbench.
- Check the cylinder for existence of signs of development of leaks from the back party of primary piston, in case of need replace assembly.
- On models with RKPP disconnect from the GTTs tank a hose of the operator of the drive of coupling (10b), - at once to a zakuporta the open end of the nipple socket.
- Pump out brake fluid from the tank (10), then, having pulled vertically, remove it from assembly of GTTs (1).
- Check a condition of sealing landing plugs (9), in case of need make replacement.
- Installation is made upside-down, - do not forget to replace a sealing ring (1a) and самоконтрящиеся nuts of fastening of the cylinder.
- In conclusion pump over the brake system (see the Section Pumping of the Brake System).
|
|
|
|