Mercedes M-Class W163

since 1997 release

Repair and operation of the car



Mercedes W163
+ Mercedes-Benz cars of a class M (W163)
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ A power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
- Body
   - External equipment and body elements
      Removal and installation of levers of screen wipers
      Removal of the drive of forward screen wipers
      Removal and installation of sliding telescopic snuffled faroomyvatel
      Removal, installation and adjustment of a cowl
      Replacement of loops of a cowl
      Removal and installation of an emblem Mercedes
      Removal, installation and service of components of the lock of a cowl
      Removal and installation of a gas-filled emphasis of fixing of a cowl in open situation
      Removal and installation of the tank of the washing liquid
      Removal and installation of a front bumper
      Removal and installation of the top forward cross beam of a frame
      Removal and installation of panels of the lower protection of a motive compartment
      Removal and installation of a rear bumper
      Removal and installation of the external holder of a spare wheel (at the corresponding complete set)
      Removal and installation of loker of protection of wheel arches
      Removal and installation of doors
      Removal and installation of limiters of opening of side doors
      Removal and installation of loops of a door of a back
      Removal and installation of a gas-filled sliding emphasis of a door of a back
      Removal and installation of external handles of doors
      Removal and installation of panels of an internal upholstery of door assemblies
      Removal and installation of door locks
      Removal and installation of door rear-view mirrors
   + Equipment of salon
+ Onboard electric equipment


Removal, installation and service of components of the lock of a cowl

Lock

Details of installation of components of the lock of a cowl

Release models till 31.08.99

Release models from 01.09.99

Scheme of putting lubricant (release model till 31.08.99)

Scheme of putting lubricant (release model from 01.09.99)


 PERFORMANCE ORDER

  1. Details of installation of components of the lock are shown on an illustration to which all references which are found in the text belong.
  2. Open a cowl and record it in vertical position.
  3. Turn out screws (1) and, having pulled up, remove the lower section (2) of castle assembly.
  4. Remove the latch otpuskaniye lever in under the dashboard in interior of the car at the left and disconnect from it a driving cable (models till 31.08.99) / disunite the contact socket of an electrical wiring (4) (model from 01.09.99).
  5. Disconnect a cable of an otpuskaniye of a latch (3) from the lower section (2) of castle assembly and remove the last from a cross beam.
  6. Turn out screws (4 and 5) and remove the top section (6) of the lock, on models till 31.08.99 equipped with a safety clamp.
  7. Installation is made upside-down.
  8. In conclusion adjust the provision of a cowl (see the Section Removal, installation and adjustment of a cowl), make sure of reliability of its fixing in a closed position and grease with jellied lubricant open elements of castle assembly (including a safety hook) and loops. Check freedom and smoothness of the course of a safety hook.

Cable of an otpuskaniye of a castle latch

Details of installation of a driving cable of an otpuskaniye of a latch of the lock of a cowl


 PERFORMANCE ORDER

  1. Details of installation of a driving cable of an otpuskaniye of a latch of the lock of a cowl are shown on an illustration to which all references which are found in the text belong.
  2. Open a cowl and record it in vertical position.
  3. Remove the top cross beam of a frame (see the Section Removal and installation of the top forward cross beam of a frame).
  4. Remove the cowl lock (see above).
  5. Release a driving cable from intermediate clamps under the top cross beam of a frame.
  6. Turn out fixing screws / release clamps and uncover the assembly block of safety locks/relay (see the Head Onboard electric equipment).
  7. In case of need remove intermediate clamps (1) of laying of a driving cable.
  8. Uncover under the dashboard at the left (see the Section Removal and installation of the lower covers of the dashboard).
  9. Remove panels of finishing of the left foot well (see the Section Removal and installation of panels of finishing of forward foot wells).
  10. Release a driving cable from a clamp on a well wall.
  11. Remove the plug through passage (2) cables from the assembly block of safety locks/relay.
  12. Involve a driving cable (3) through a partition in a motive compartment.
  13. Installation is made upside-down, - track correctness of laying of a cable.